Question about item
Description
5 volts, 40 amps, 200 watts — built-in power supply in a metal case
The MEAN WELL RSP-200-5 is an enclosed built-in power supply with 5 V and 200 W, universal input and active power factor correction. The output is adjustable from 4.5 to 5.5 V. It is cooled without a fan by free-air convection and therefore runs silently.
- Is it right for my project?
- Technical data
- Connection
- Safety
- Scope of delivery
- Frequently asked questions
Is it right for my project?
What this power supply is made for
- 5 V pixels and 5 V pixel strips such as WS2812B, SK6812 or APA102 — around 660 RGB pixels at full brightness
- Installation in control cabinets, distribution boards and enclosures: 215 × 115 × 30 mm
- Universal input 88–264 V AC / 124–370 V DC — the same unit for mains worldwide
- Exact voltage at the load: output adjustable from 4.5 to 5.5 V
What it is not for
- 12 V devices — see the 12 volt power supplies
- Other ratings and designs are under power supplies
- Outdoor use, damp environments or use without an enclosure: it is a built-in power supply for dry rooms, not a weatherproof unit
- Connection by non-specialists: the 230 V mains connection must be made by a qualified electrician
Also required: a mains lead with earth conductor, an installation location with protection against contact and fusing of the outputs.
40 AOutput current at 5 V
200 WOutput power
no fanfree-air convection
> 0.95Power factor at 230 V AC (active PFC)
Protected and monitored
- Overload: from 105–135 % of rated power the power supply switches to hiccup mode and recovers automatically once the fault is removed
- Overvoltage: shutdown at 5,75–7 V at the output, restart by switching off and on again
- Overtemperature: shutdown, then automatic restart
- Cooling by free-air convection, no fan
- An LED indicates that output voltage is present
Connection
Up and running in four steps
- Work de-energised. Before any installation, disconnect the system from the mains and secure it against being switched back on.
- Mount. The standard mounting orientation is horizontal. Keep ventilation openings clear and keep 10–15 cm away from other heat sources; other mounting orientations and high ambient temperatures require derating per the datasheet. Only use fixing screws of the length stated in the datasheet.
- Connect the output. Loads to −V and +V, distribute the current across all output terminals. Choose the conductor cross-section according to the current per lead — the table is in the installation manual; fuse each feed individually.
- Connect the mains and switch on. Connect L, N and the earth conductor; the earth conductor (FG) must be connected to earth. After switching on, measure the voltage at the load and adjust at the potentiometer if necessary.
Caution: The output voltage must suit your pixels — 5 V pixels do not tolerate overvoltage. Never set the potentiometer above the value stated by the pixel manufacturer.
Safety
Safety instructions
- Risk of electric shock: installation and mains connection by a qualified electrician only; have faults checked by a specialist. Do not open the case.
- Do not install in places with high humidity or near water.
- Do not operate at high ambient temperature or near sources of fire. Operating temperature −30 to +70 °C; at high temperatures and in other mounting orientations the load must be reduced (derating curve in the datasheet).
- Output current and output power must not exceed the rated values (40 A, 200 W).
- The power supply is a component for installation in end equipment; electromagnetic compatibility must be re-verified in the finished installation.
The complete instructions are in the manufacturer's installation manual in the Documents section.
Scope of delivery
- MEAN WELL RSP-200-5 switching power supply
Mains lead, fuses, loads and mounting material are not included.
Documents
The RSP-200 series datasheet and the installation manual in German and English are in the Documents section on this page.
The pictures show a unit of the RSP-200 series and the derating curve from the datasheet.
Frequently asked questions
How many pixels can I power with it?
As a rule of thumb, an RGB pixel draws around 60 mA at full brightness in white. 40 A is therefore enough for about 660 pixels. In operation with colours and dimmed effects the current is usually much lower; the pixel manufacturer's figures are decisive. Plan some reserve instead of running the power supply permanently at rated load.
Can I adjust the output voltage?
Yes, at the potentiometer next to the terminal strip in the range 4.5 to 5.5 V. Only adjust so far that the load receives the voltage stated by its manufacturer.
Is the power supply noisy?
No, it has no fan and is cooled by free-air convection.
Which standards has the unit been tested to?
According to the manufacturer, UL 62368-1 and — tested by TÜV — EN 62368-1. The details are in the datasheet in the Documents section.
Technical data
| Item information | Value |
|---|---|
| Output power: | 200 W |
| Ambient operating temperature: | −30 to +70 °C (derating per datasheet) |
| Output voltage: | 5 V DC (adjustable 4.5–5.5 V) |
| Enclosure: | Metal, enclosed |
| Input voltage: | 88–264 V AC / 124–370 V DC, 47–63 Hz |
| Output current: | 0–40 A |
| Mounting: | Built-in, screw mounting |
| Dimensions: | 215 × 115 × 30 mm |
| Weight: | 0.72 kg |
| Ripple & noise: | max. 150 mVp-p |
| Efficiency: | typ. 85.5 % |
| Power factor: | > 0.95 at 230 V AC (active PFC) |
| Protection functions: | Short circuit, overload, overvoltage, overtemperature |
| Cooling: | Free-air convection (no fan) |
| Shipping weight: | 0,80 kg |
Product safety information
Manufacturer information:
MEAN WELL EUROPE N.V.
Langs de Werf 8
NL-1185 XT Amstelveen
Niederlande
info@meanwell.eu
https://www.meanwell.eu
Langs de Werf 8
NL-1185 XT Amstelveen
Niederlande
info@meanwell.eu
https://www.meanwell.eu
