Question about item
Description
150 individually addressable RGB pixels on 5 metres, for dry indoor rooms
This LED pixel strip carries 30 WS2812b LEDs per metre. Every LED has its control chip built in and can be set individually in colour and brightness. The strip runs on 5 volts and has no moisture protection.
Is it right for my project?
What this strip is made for
- Chasers, colour gradients and effects where every LED shows something different
- Outlines, lettering, advertising displays and Christmas lighting
- Dry indoor rooms, e.g. furniture, showcases and displays
- Control with pixel controllers that support WS2812
Not suitable for
- Operation on 12 or 24 volts — the strip is for 5 volts only
- Pure white light for room lighting — white is mixed from red, green and blue here and looks cool
- Use without a controller — the strip needs a data signal
- Damp rooms and outdoor use — the strip is not protected against moisture
Also required: a 5 V power supply with sufficient power and a pixel controller.
150LEDs on 5 m
5 Voperating voltage
max. 45 Wat full brightness, all colours
IP30protection rating, dry use only
Connection
Up and running in four steps
- Mind the direction. The arrows on the PCB show the data direction (DIN → DO). Connect the controller to the end marked “DIN”.
- Choose the power supply. Allow up to 0.3 W per LED, i.e. up to 45 W (9 A at 5 V) for 5 m, plus about 20 % reserve.
- Inject power. At full brightness the voltage drops along the strip — inject power at both ends so the colours do not fade towards the end.
- Switch on. Make all connections first, then switch on the power supply.
Caution: Operate on 5 V only and only in dry indoor rooms.
Safety
Safety instructions
- Operate only on a 5 V power supply (safety extra-low voltage); choose a supply with about 20 % power reserve.
- Connect or disconnect only with the power switched off.
- Do not use a damaged strip.
- Do not kink the strip or run it over sharp edges; avoid mechanical stress and sources of heat.
- Operating temperature −15 to +60 °C.
- Not a toy — keep out of the reach of children.
Scope of delivery
- 1 LED pixel strip, 5 m
Power supply and controller are not included.
Documents
The datasheet is available in the Documents section on this page.
Frequently asked questions
Can I shorten the strip?
Yes, at the marked cutting points between the LEDs.
Which controller fits?
Any pixel controller that outputs the WS2812 protocol.
Why does the end get darker or reddish?
At full brightness the voltage drops along the strip. Inject power at both ends and use sufficiently thick supply leads.
Technical data
| Item information | Value |
|---|---|
| Controller IC: | WS2812b |
| Ambient operating temperature: | -15 to +60 °C |
| Pixel spacing: | 33.3 mm |
| Power (string): | max. 45 W (150 px) |
| Design current (string): | approx. 9 A (150 px @ full white) |
| Dimensions: | 5 m × 10 mm |
| Form factor: | Pixel strip |
| LEDs per metre: | 30 |
| Number of pixels: | 150 |
| Operating Voltage: | 5 Volt DC |
| Protection class: | IP30 |
| WEEE-Reg.-Nr.: | DE 32487762 |
| Colour (PCB): | white |
| Shipping weight: | 0,09 kg |
| Content: | 5,00 m |
Product safety information
Manufacturer information:
PIXLtec GmbH
Maybachstraße 8
Baden-Württemberg
76227 Karlsruhe
Deutschland
info@pixltec.de
Maybachstraße 8
Baden-Württemberg
76227 Karlsruhe
Deutschland
info@pixltec.de
