Four powered outputs for data-only pixels at the end of the long-range line
The PixLite® R4D-S is the receiver for the long-range transmitter
T8-S Mk3: it sits up to 300 m from the transmitter right at the pixels, takes the
data in over a network cable and outputs it on four fused outputs together with the pixel power. Designed for
data-only pixels such as WS2811, WS2812B or SK6812 — the transmitter runs the line in expanded mode with four
outputs of 510 pixels each.
Is it right for my project?
What this receiver is made for
- As the counterpart to the T8-S Mk3 — one receiver per line, up to eight on the
transmitter
- Four shorter pixel strings of up to 510 RGB pixels each directly at the receiver, powered from a local power
supply (5–24 V, up to 6 A per output, 24 A in total) — more strings, fewer injection points
- Data-only pixels: WS2811, WS2812B, WS2815, SK6812 and all other chips without a clock line
- Little space: 95 × 78 × 33 mm, on a flat surface or on a DIN rail with the kit
Not for
- Clocked pixels (CLK + DATA) such as APA102 or long strings of up to 1,020 pixels per output: that is what the
R2F-S with two outputs is for
- On the T16X-S Mk3: there the R1F-S and R2F-S
work, not the R4D-S
- Without a transmitter: the R4D-S only understands the long-range signal — no Art-Net, no sACN, no network
connection
- Direct outdoor mounting without an enclosure: the unit is designed for installation, not for rain
Also required: a T8-S Mk3, a network cable (Cat 5 or Cat 6, up to 300 m), a power supply matching
the voltage of your pixels (5–24 V) and the pixels themselves. Matching
power
supplies and
xConnect® cabling are in our range.
4powered outputs, up to 510 RGB pixels each
6 Aper output, 24 A in total
300 mdistance to the transmitter over network cable
7.5 Ablade fuse per output, replaceable
Wiring
Up and running in three steps
-
Mount and power the receiver. At the pixels, screw it onto a flat surface or put it on the DIN
rail with the DIN rail kit; power supply in the pixel voltage (5, 12 or 24 V) to
the quick-connect clamp.
-
Connect the pixels. Per output +, DATA and −.
-
Connect to the transmitter. Network cable from the T8-S output into the RJ45 socket (up to
300 m); on the transmitter, set the line to expanded mode in the browser and assign the universes.
Caution: power supply and pixels must have the same voltage — 12 V on 5 V pixels destroys them
instantly. The RJ45 socket is not a network port: it belongs on a PixLite transmitter, not on a switch.
Scope of delivery
- PixLite® R4D-S long-range receiver with pluggable terminals
- Installation guide
Transmitter, power supply, pixels, network cable and DIN rail kit are not included.
Documents
Datasheet, long-range quick start guide and user manual are in the documents section on this page. Which
pixels the system understands is in the protocol list — it applies to the
transmitter.
Frequently asked questions
How many pixels can one R4D-S handle?
510 RGB or 384 RGBW pixels per output, twelve universes together. The second limit is the
current: 6 A per output, 24 A in total — with power-hungry pixels at full brightness it is reached before the
pixel count; then split the strings or inject additionally.
Why data-only pixels only?
In expanded mode the T8-S splits each line into four outputs — the clock line is dropped in
the process. Chips without a clock (WS2811, WS2812B, WS2815, SK6812 …) do not need it; for clocked chips such as
APA102 take the
R2F-S.
What happens when a fuse blows?
The "Fuse good" LED of that output goes out, the other outputs keep running. Fix the cause,
open the flap, replace the 7.5 A mini blade fuse (automotive standard).
Unsure about receiver choice, power supplies and cable routing? Describe your project to us — we work out the
power budget and parts list and get back to you with a proposal.
Discuss your project
Product safety information
Manufacturer information:
Advatek
Unit 1, 3 - 5 Gilda Court, Mulgrave
3170 VIC
Australien
support@advateklights.com
