Question about item
Description
100 addressable RGB pixels (3 LEDs each) on 5 metres, protected to IP65
This LED pixel strip carries 60 LEDs per metre. Three LEDs share one WS2811 control chip and form a pixel that can be set in colour and brightness. The strip runs on 12 volts and is protected to IP65.
Is it right for my project?
What this strip is made for
- Chasers, colour gradients and effects in sections of three LEDs
- Outlines, lettering, advertising displays and Christmas lighting
- Indoors and in sheltered outdoor areas (IP65)
- Control with pixel controllers that support WS2811
Not suitable for
- Operation on 5 or 24 volts — the strip is for 12 volts only
- Pure white light for room lighting — white is mixed from red, green and blue here and looks cool
- Use without a controller — the strip needs a data signal
Also required: a 12 V power supply with sufficient power and a pixel controller.
100pixels (3 LEDs each) on 5 m
12 Voperating voltage
max. 72 Wat full brightness, all colours
IP65protection rating
Connection
Up and running in four steps
- Mind the direction. The arrows on the PCB show the data direction (DIN → DO). Connect the controller to the end marked “DIN”.
- Choose the power supply. Allow up to 0.72 W per pixel (60 mA at 12 V), i.e. up to 72 W (6 A at 12 V) for 5 m, plus about 20 % reserve.
- Inject power. The additional leads are for power injection. At full brightness the voltage drops along the strip — inject power at both ends so the colours do not fade towards the end.
- Switch on. Make all connections first, then switch on the power supply.
Caution: Operate on 12 V only. After cutting, the cut point is no longer protected to IP65.
Safety
Safety instructions
- Operate only on a 12 V power supply (safety extra-low voltage); choose a supply with about 20 % power reserve.
- Connect or disconnect only with the power switched off.
- Do not use a damaged strip.
- Do not kink the strip or run it over sharp edges; avoid mechanical stress and sources of heat.
- Operating temperature −15 to +60 °C.
- Not a toy — keep out of the reach of children.
Scope of delivery
- 1 LED pixel strip, 5 m, with connection leads
Power supply and controller are not included.
Documents
The datasheet is available in the Documents section on this page.
Frequently asked questions
Can I shorten the strip?
Yes, at the marked cutting points after every three LEDs. The cut end is then open and must be sealed again for outdoor use.
Which controller fits?
Any pixel controller that outputs the WS2811 protocol.
Why does the end get darker or reddish?
At full brightness the voltage drops along the strip. Inject power at both ends and use sufficiently thick supply leads.
Technical data
| Item information | Value |
|---|---|
| Ambient operating temperature: | -15 to +60 °C |
| Pixel spacing: | 50 mm |
| Power (string): | max. 72 W (100 px) |
| Design current (string): | approx. 6 A (100 px @ full white) |
| Dimensions: | 5 m × 10 mm |
| Connection: | 3-pin plug, additional power injection leads |
| Form factor: | Pixel strip |
| LEDs per metre: | 60 |
| Number of pixels: | 100 |
| Controller IC: | WS2811 |
| WEEE-Reg.-Nr.: | DE 32487762 |
| Operating Voltage: | 12 Volt DC |
| Colour (PCB): | white |
| Protection class: | IP65 |
| Shipping weight: | 0,30 kg |
| Content: | 5,00 m |
Product safety information
Manufacturer information:
PIXLtec GmbH
Maybachstraße 8
Baden-Württemberg
76227 Karlsruhe
Deutschland
info@pixltec.de
Maybachstraße 8
Baden-Württemberg
76227 Karlsruhe
Deutschland
info@pixltec.de
